CWNA-108 Certified Wireless Network Administrator Questions and Answers

The likely problem that causes this scenario is faulty drivers. Drivers are software components that enable the communication between the operating system and the hardware devices, such as the wireless adapters. Faulty drivers can cause various issues with the wireless connectivity, such as not detecting or connecting to certain networks, dropping connections, or reducing performance. Faulty drivers can be caused by corrupted files, outdated versions, incompatible settings, or hardware defects. To fix faulty drivers, you can try to update, reinstall, or roll back the drivers, or contact the manufacturer for support. Interference from non-Wi-Fi sources, DoS attack, or interference from other WLANs are not likely to cause this scenario, as they would affect all devices in the same area, not just the new laptops. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 562; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 532.

TWT is the feature of 802.11ax (HE) that is managed with beacon and trigger frames and is primarily a power management method, but also provides more efficient access to the channel used within a BSS. TWT stands for target wake time, which is a mechanism that allows an access point and a client device to negotiate and schedule specific times for data transmission and reception. This enables the client device to enter a low-power sleep mode when it is not expected to communicate with the access point, which saves battery life and reduces power consumption. TWT also reduces contention and interference on the channel used within a BSS, as it coordinates the transmissions of multiple client devices and avoids collisions. TWT is managed with beacon and trigger frames, which are two types of management frames that are used to announce and initiate data exchanges. A beacon frame is a frame that is periodically sent by an access point to advertise its presence, capabilities, and parameters to client devices. A trigger frame is a frame that is sent by an access point or a client device to request or initiate a data transmission with another device. BSS color, UL-MU-MIMO, and OFDMA are other features of 802.11ax (HE) that are not primarily power management methods, but rather performance enhancement methods. BSS color is a feature that assigns a color code to each BSS to differentiate it from other BSSs that use the same channel. This reduces interference and improves spatial reuse of the channel. UL-MU-MIMO is a feature that allows an access point to receive multiple simultaneous transmissions from different client devices using multiple spatial streams. This increases capacity and throughput of the uplink direction. OFDMA is a feature that divides a channel into smaller subchannels called resource units (RUs) that can be allocated to different devices for concurrent transmissions. This increases efficiency and flexibility of the channel utilization. References: CWNA-109 Study Guide, Chapter 10: Wireless LAN Operation, page 323

The guard interval is a short period of time inserted between the symbols of an OFDM signal to prevent inter-symbol interference and improve the robustness of the transmission1. The guard interval can have different values depending on the 802.11 standard and the configuration of the device. For example, 802.11n supports two guard intervals: 800 ns (normal) and 400 ns (short)2. 802.11ac supports the same guard intervals as 802.11n, plus an optional 200 ns guard interval for 80 MHz and 160 MHz channels3. 802.11ax supports three guard intervals: 800 ns, 1600 ns, and 3200 ns4.

The guard interval affects the data rate because it determines the duration of each symbol. A shorter guard interval means more symbols can be transmitted in a given time, resulting in a higher data rate. However, a shorter guard interval also means less protection against inter-symbol interference, which may degrade the signal quality and increase the error rate. Therefore, there is a trade-off between data rate and reliability when choosing the guard interval.

The MCS tables for HT and VHT PHY devices show the data rates for different combinations of modulation, coding, channel width, spatial streams, and guard intervals. For example, for a VHT device using MCS 9 with QAM-256 modulation, 5/6 coding rate, 80 MHz channel width, and one spatial stream, the data rate is 433.3 Mbps with a normal guard interval (800 ns) and 486.7 Mbps with a short guard interval (400 ns)2. Therefore, the guard interval impacts the data rate according to the MCS tables.

Return loss is a measure of how well the components of an RF system are matched in terms of their impedance. Impedance is the opposition to the flow of alternating current in a circuit, and it depends on the frequency, resistance, capacitance, and inductance of the components. When the impedance of the source, the transmission line, and the load are not equal, some of the power is reflected back to the source, causing a loss of forward power. This loss is expressed in decibels (dB) as return loss. The higher the return loss, the lower the reflection and the better the impedance matching. Conversely, the lower the return loss, the higher the reflection and the worse the impedance matching.

VSWR (Voltage Standing Wave Ratio) is another way of expressing the same concept. It is the ratio of the maximum voltage to the minimum voltage along a transmission line due to the interference of the incident and reflected waves. A VSWR of 1:1 means that there is no reflection and perfect impedance matching. A VSWR higher than 1:1 means that there is some reflection and impedance mismatch. The higher the VSWR, the higher the reflection and the lower the return loss.

Therefore, a significant impedance mismatch between components in an RF system will cause high reflection, high VSWR, and low return loss.

An IBSS is used instead of a BSS is a network configuration that would result in multiple stations broadcasting Beacon frames with the same BSSID but with different source addresses. An IBSS (Independent Basic Service Set) is a type of WLAN that does not use an AP but rather allows stations to communicate directly with each other in a peer-to-peer manner. An IBSS is also known as an ad-hoc network or a peer-to-peer network. In an IBSS, each station generates its own Beacon frames to announce its presence and capabilities to other stations within range. The Beacon frames have the same BSSID, which is randomly generated by one of the stations when creating the IBSS, but they have different source addresses, which are the MAC addresses of each station’s radio interface. The BSSID is used to identify the IBSS and prevent stations from joining other IBSSs with different BSSIDs. References: , Chapter 1, page 25; , Section 1.1

OFDM (Orthogonal Frequency Division Multiplexing) is the physical layer specification (PHY) that VHT capable devices must be backward compatible with according to the IEEE 802.11-2012 standard. VHT (Very High Throughput) is a PHY and MAC enhancement that is defined in the IEEE 802.11ac amendment and is also known as Wi-Fi 5. VHT operates only in the 5 GHz band and uses features such as wider channel bandwidths (up to 160 MHz), higher modulation schemes (up to 256-QAM), more spatial streams (up to eight), multi-user MIMO (MU-MIMO), beamforming, and VHT PHY and MAC enhancements. VHT can achieve data rates up to 6.9 Gbps.

According to the IEEE 802.11-2012 standard, VHT capable devices must be backward compatible with devices using OFDM PHY, which is defined in the IEEE 802.11a amendment and is also used by IEEE 802.11g, IEEE 802.11n, and IEEE 802.11h amendments. OFDM operates in both the 2.4 GHz and 5 GHz bands and uses features such as subcarriers, symbols, guard intervals, and OFDM PHY and MAC enhancements. OFDM can achieve data rates up to 54 Mbps.

Backward compatibility means that VHT capable devices can interoperate with OFDM devices on the same network by using common features and parameters that are supported by both PHYs. For example, VHT capable devices can use a channel bandwidth of 20 MHz, a modulation scheme of BPSK, QPSK, or 16-QAM, one spatial stream, no beamforming, and OFDM PHY and MAC headers when communicating with OFDM devices. Backward compatibility also means that VHT capable devices can fall back to OFDM mode when the signal quality or SNR is too low for VHT mode. References: 1, Chapter 3, page 123; 2, Section 3.2

Weak signal strength is the likely cause of the low data rate issue for the client that has a signal strength of -84 dBm and a noise floor of -96 dBm. The client is an 802.11ac client and connects to an 802.11ac AP. Both the client and AP are 2x2:2 devices. Signal strength is the measure of how strong the RF signal is at the receiver. Signal strength can affect the reliability and performance of the wireless connection, as well as the data rate and throughput of the traffic. The higher the signal strength, the better the signal quality and the higher the data rate. The lower the signal strength, the worse the signal quality and the lower the data rate.

The data rate of an 802.11ac connection depends on several factors, such as channel bandwidth, modulation and coding scheme (MCS), spatial streams, guard interval, and beamforming. However, these factors are also influenced by the signal strength, as they require a certain signal-to-noise ratio (SNR) to operate properly. SNR is the ratio of the signal strength to the noise floor, which is the measure of the background noise or interference in the RF environment. The higher the SNR, the more robust and efficient the communication. The lower the SNR, the more prone and vulnerable to errors and retries.

According to the CWNA Official Study Guide , Table 3.7, page 112, an 802.11ac connection with a channel bandwidth of 80 MHz, an MCS of 9, two spatial streams, a short guard interval, and no beamforming can achieve a maximum data rate of 867 Mbps. However, this data rate requires a minimum SNR of 30 dB to maintain a sufficient signal quality. If the signal strength is -84 dBm and the noise floor is -96 dBm, then the SNR is only 12 dB (-84 dBm - (-96 dBm) = 12 dB), which is far below the required SNR for this data rate. Therefore, the data rate will drop significantly to match the lower SNR and signal quality.

To solve this problem, the signal strength should be increased to improve the SNR and data rate. This can be done by adjusting the output power or channel assignment of the AP or client, relocating or reorienting some APs or antennas to reduce attenuation or interference, updating or replacing some faulty or outdated hardware or software components, etc. References: , Chapter 3, page 112; , Section 3.2

The client STA can use Beacon frames transmitted by the AP to verify that an AP supports the same data rates that it supports. Beacon frames are management frames that are periodically broadcasted by the APs to announce their presence, capabilities, and parameters. One of the information elements contained in the Beacon frames is the Supported Rates or Extended Supported Rates, which lists the data rates that the AP can use for communication. The client STA can compare its own data rates with those advertised by the AP to determine if they are compatible. Data frames, authentication frames, and probe request frames do not contain information about data rates. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 133; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 123.

The authentication method that is referenced in the 802.11-2016 and 802.11-2020 specifications and is recommended for robust WLAN client security is 802.1X/EAP. 802.1X/EAP stands for IEEE 802.1X Port-Based Network Access Control with Extensible Authentication Protocol and is a framework that provides strong authentication and dynamic encryption key generation for WLAN clients. 802.1X/EAP involves three parties: the supplicant (the client), the authenticator (the AP or the controller), and the authentication server (usually a RADIUS server). The supplicant sends its credentials (such as username and password, certificate, or token) to the authenticator, which forwards them to the authentication server. The authentication server verifies the credentials and sends a response to the authenticator, which grants or denies access to the supplicant. The authentication server also generates a master key that is used to derive encryption keys for the data frames between the supplicant and the authenticator. 802.1X/EAP supports various EAP methods that offer different levels of security and flexibility, such as EAP-TLS, EAP-PEAP, EAP-TTLS, EAP-FAST, and EAP-SIM. SSL, IPSec, and WEP are not authentication methods, but rather encryption or security protocols that are not specific to WLANs or referenced in the 802.11 specifications. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 299; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 289.

A high-density deployment is a wireless network that is designed to support a large number of users and devices in a relatively small area. This type of deployment is often used in enterprise environments, such as offices, schools, and hospitals.

The use of semi-directional antennas in the deployment described in the question is a good indication that it is a high-density deployment. Semi-directional antennas can be used to focus the signal from an access point in a specific direction. This can help to reduce interference and improve performance in high-density environments.

The other answer choices are less likely to be correct for the following reasons:

• SOHO (small office/home office) deployments are typically smaller and less complex than high-density deployments.
• Residential deployments are typically even smaller and less complex than SOHO deployments.
• Standard office deployments may be high-density, but they may also be lower-density.

It is important to note that the type of deployment is not determined solely by the output power of the access points. However, the use of 10 mW of output power on the 2.4 GHz radios and 20 mW of output power on the 5GHz radios is also consistent with a high-density deployment.

Here are some additional tips for deploying a high-density wireless network:

• Use a site survey to determine the optimal placement of access points.
• Configure the access points to use non-overlapping channels.
• Use semi-directional or directional antennas to focus the signal and reduce interference.
• Implement a wireless intrusion prevention system (WIPS) to detect and mitigate rogue access points and other security threats.

Calibrating the floor plan is what you must do before gathering survey data after the floor plan is imported when using a site survey tool for post-implementation validation. A site survey tool is a software application that can run on a laptop, tablet, smartphone, or other device that has a Wi-Fi adapter and a GPS receiver. A site survey tool can scan the wireless environment and collect information about the detected access points and client stations, such as their SSID, BSSID, channel, signal strength, security, and data rate. A site survey tool can also measure and display various metrics of network performance, such as throughput, jitter, packet loss, delay, and SNR. A site survey tool can also use a floor plan to visualize the wireless coverage and quality in different locations on a map. A floor plan is an image file that shows the layout and dimensions of a building or an area where the WLAN is deployed. A floor plan can be imported from various sources, such as a CAD file, a PDF file, an image file, or a Google Maps screenshot. After importing a floor plan into a site survey tool, it is necessary to calibrate the floor plan before gathering survey data. Calibrating the floor plan means adjusting the scale and orientation of the floor plan to match the actual size and direction of the area. Calibrating the floor plan can be done by using a reference point or a reference line that has a known distance or angle in the real world. Calibrating the floor plan ensures that the survey data is accurate and consistent with the physical environment. References: 1, Chapter 7, page 290; 2, Section 4.3

WLAN bridges must use a channel with acceptable SNR at both transceivers to maintain the desired data rate bi-directionally. A WLAN bridge is a device that connects two or more networks using the 802.11 protocol. A WLAN bridge must have a clear and strong signal between the two endpoints to ensure reliable and fast data transmission. The signal-to-noise ratio (SNR) is a measure of the quality of the signal, which depends on the distance, interference, obstacles, and antenna gain between the transceivers. A higher SNR means a better signal quality and a higher data rate. A lower SNR means a worse signal quality and a lower data rate. Therefore, a WLAN bridge must use a channel with acceptable SNR at both transceivers to maintain the desired data rate bi-directionally1.

The unit of measurement that is an absolute unit and is used to quantify received signal power levels on a logarithmic scale is dBm. dBm stands for decibel-milliwatt and represents the power level relative to 1 milliwatt (mW). dBm is an absolute unit because it has a fixed reference point and does not depend on the input power level. dBm is used to measure the received signal power levels on a logarithmic scale because it can express large variations in power levels with small numbers and make calculations easier. For example, a 10 dB increase in power level means a 10-fold increase in power, and a 20 dB increase means a 100-fold increase in power. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 66; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 56.

VoIP (Voice over Internet Protocol) is an application that is likely used that demands the requirements of unidirectional delays of less than 150 ms and the signal strength at all receivers can be no lower than -67 dBm. VoIP is an application that allows users to make and receive voice calls over a network, such as the Internet or a WLAN. VoIP is a real-time and interactive application that requires high quality of service (QoS) to ensure good user experience and satisfaction. One of the QoS metrics for VoIP is delay, which is the time it takes for a voice packet to travel from the sender to the receiver. Delay can affect the quality and intelligibility of the voice conversation, as well as the synchronization and naturalness of the dialogue. The ITU-T G.114 recommendation suggests that the maximum acceptable one-way delay for VoIP should be less than 150 ms, as anything higher than that can cause noticeable degradation and annoyance to the users. Another QoS metric for VoIP is signal strength, which is the measure of how strong the RF signal is at the receiver. Signal strength can affect the reliability and performance of the wireless connection, as well as the data rate and throughput of the VoIP traffic. The CWNA Official Study Guide recommends that the minimum signal strength for VoIP should be -67 dBm, as anything lower than that can cause packet loss, retries, jitter, and other issues that can impair the voice quality. References: 1, Chapter 10, page 398; 2, Section 6.1

In an 802.11 2.4 GHz system, channels 1 and 5 are considered non-overlapping. In the 2.4 GHz band, there are 14 channels defined by the IEEE 802.11 standard, but only 11 of them are available in North America and most other regions. Each channel has a bandwidth of 22 MHz, but they are spaced only 5 MHz apart from each other. This means that adjacent channels overlap with each other and cause interference. To avoid interference, it is recommended to use only non-overlapping channels, which are channels that do not share any frequency range with each other. In the 2.4 GHz band, there are only three non-overlapping channels: channel 1, channel 6, and channel 11. However, some devices can use channel bonding to combine two adjacent channels into one wider channel of 40 MHz, which can provide higher throughput but also more interference. In this case, there are only two non-overlapping channels: channel 1+5 and channel 6+10. References: 1, Chapter 3, page 86; 2, Section 3.2

A POE device that requires 47 W of power should use the 802.3bt specification. This is because 802.3bt is the latest POE standard that supports up to 90 W of power delivery over four pairs of wires in an Ethernet cable. The previous POE standards, such as 802.3af and 802.3at, only support up to 15.4 W and 30 W of power delivery over two pairs of wires in an Ethernet cable, respectively. Therefore, they are not sufficient for powering a device that requires 47 W of power. The 802.11at specification does not exist; it is a typo or confusion with the 802.3at specification. References: CWNA-109 Study Guide, Chapter 8: Wireless LAN Access Points, page 2431

The center frequency of channel 4 in the 2.4 GHz band is 2.427 GHz (2427 MHz). The center frequency of a channel is the midpoint of its frequency range, where the signal strength is highest and most concentrated. The center frequency of channel 1 in the 2.4 GHz band is 2.412 GHz (2412 MHz), as given in the question. The center frequency of each subsequent channel is obtained by adding 5 MHz to the previous channel’s center frequency, since the channels are spaced 5 MHz apart from each other in this band. Therefore, to find the center frequency of channel 4, we need to add 15 MHz (5 MHz x 3) to the center frequency of channel 1:

2.412 GHz + 0.015 GHz = 2.427 GHz

Alternatively, we can use a formula to calculate the center frequency of any channel in the 2.4 GHz band:

Center frequency (GHz) = 2.407 + (0.005 x Channel number)

Using this formula for channel 4, we get:

Center frequency (GHz) = 2.407 + (0.005 x 4)

Center frequency (GHz) = 2.407 + 0.02

Center frequency (GHz) = 2.427 References: 1, Chapter 3, page 85; 2, Section 3.2

Impedance is the measure of opposition to the flow of alternating current (AC) in a circuit. Impedance mismatch occurs when the impedance of the radio does not match the impedance of the antenna or the cable. This causes some of the transmitted or received signal to be reflected back, resulting in a loss of power and efficiency. The voltage standing wave ratio (VSWR) is a metric that indicates the amount of impedance mismatch in a transmission line. A higher VSWR means a higher impedance mismatch and a lower signal quality. A VSWR of 1:1 is ideal, meaning there is no impedance mismatch and no reflected power. A VSWR of 2:1 means that for every 2 units of forward power, there is 1 unit of reflected power12.

The other options are not correct because they do not affect the VSWR in RF cables. A high gain yagi antenna or a high gain parabolic dish antenna can increase the signal strength and directionality, but they do not cause impedance mismatch in the cable. Radio output power above 100 mW but below 400 mW is within the acceptable range for most WLAN devices and does not cause excessive VSWR in the cable3.

References: 1: CWNA-108 Official Study Guide, page 77 2: VSWR 3: CWNA-108 Official Study Guide, page 81

It is a channel that may require DFS when used is an important fact that should be considered about channel 128. Channel 128 is a 5 GHz frequency band 20 MHz channel that has a center frequency of 5.64 GHz. Channel 128 is one of the channels that are subject to DFS (Dynamic Frequency Selection) rules, which require Wi-Fi devices to monitor and avoid using channels that are occupied by radar systems or other primary users. DFS is a feature that is defined in the IEEE 802.11h amendment and is mandated by some regulatory bodies, such as the FCC and the ETSI, to protect the licensed users of the 5 GHz band from interference by unlicensed Wi-Fi devices. DFS works by using a mechanism called channel availability check (CAC), which requires Wi-Fi devices to scan a channel for a certain period of time before using it. If a radar signal is detected during the CAC or while using the channel, the Wi-Fi devices must switch to another channel that is free from radar interference.

When configuring an access point to use channel 128, it is important to consider the implications of DFS rules, such as:

• The access point must support DFS and comply with the local regulations and standards that apply to DFS channels.
• The access point may experience delays or interruptions in its operation due to CAC or channel switching.
• The access point may have limited channel selection or availability due to radar interference or other Wi-Fi devices using DFS channels.
• The access point may have compatibility or interoperability issues with some client devices that do not support DFS or use different DFS parameters.
• The access point may have performance or quality issues due to co-channel or adjacent-channel interference from other Wi-Fi devices using non-DFS channels.

Therefore, it is advisable to use channel 128 only when necessary and after performing a thorough site survey and spectrum analysis to determine the best channel for the access point. References: 1, Chapter 3, page 117; 2, Section 3.2

The device in the bridge implementation that acts as the 802.1X Authenticator is the root bridge. The root bridge is the bridge that connects to the wired network and acts as the central point for all other bridges in the point-to-multipoint topology. The root bridge authenticates the non-root bridges using 802.1X/EAP and forwards their authentication requests to the RADIUS server. The non-root bridges act as the 802.1X Supplicants and use EAP methods such as EAP-TLS or EAP-PEAP to authenticate with the root bridge. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 459; [Cisco Aironet Wireless Bridges FAQ], question 29.

The final step in an effective troubleshooting process is to document the results. Documentation is essential for keeping track of the problem history, the actions taken, the solutions implemented, and the outcomes achieved. Documentation can also help to prevent future problems, improve best practices, and provide feedback for improvement. Documentation should include relevant information such as problem description, symptoms, root cause analysis, resolution steps, verification methods, and lessons learned. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 513; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 483.

Authenticated and Unassociated. According to one of the web search results1, a STA can be authenticated to multiple APs, but it can only be associated to one AP at a time. Association is the process of establishing a logical link between the STA and the AP, which allows the STA to send and receive data frames through the AP2. Therefore, when a STA has authenticated to an AP-1, but still maintains a connection with another AP-2, it means that the STA is authenticated to both APs, but only associated to AP-2. The state of the STA on AP-1 is authenticated and unassociated, which means that the STA can switch to AP-1 without repeating the authentication process, but it cannot send or receive data frames through AP-1 until it becomes associated.

Refraction is the bending of an RF signal as it passes through a material of different density. Refraction can cause the signal to change its direction and angle of arrival. For example, when a light beam passes from air to water, it bends because of the difference in the refractive index of the two mediums. Similarly, when an RF signal passes from one medium to another, such as from air to glass, it can bend due to the change in the dielectric constant of the materials12. References: 1: CWNA-108 Official Study Guide, page 67 2: Refraction

Fade Margin is an additional pad of signal strength designed into the RF system to compensate for unpredictable signal fading. It is the difference between the receiver’s sensitivity and the actual received signal level. A higher Fade Margin indicates a more robust link that can withstand interference, attenuation, or other factors that may reduce the signal strength. A lower Fade Margin means that the link is more susceptible to failure or performance degradation. Fade Margin is usually expressed in decibels (dB) and can be calculated by subtracting the receiver sensitivity from the received signal level. References: 1, Chapter 2, page 51; 2, Section 2.1

https://www.cablinginstall.com/articles/2012/08/cat-6a-vs-cat-5e-poe.html

The statement that the lowest voltage drop is achieved when using CAT6 cable instead of Cat5 or CAT5e is true about 802.3, Clause 33 Power over Ethernet. Power over Ethernet (PoE) is a technology that allows electrical power to be delivered over Ethernet cables along with data signals. PoE is defined by IEEE 802.3, Clause 33 and has several variants, such as PoE (802.3af), PoE+ (802.3at), and PoE++ (802.3bt). PoE works by using a device called PSE (Power Sourcing Equipment) that injects power into the Ethernet cable and a device called PD (Powered Device) that receives power from the Ethernet cable. The PSE can be either an endpoint device, such as a switch or a router, or a midspan device, such as an injector or a splitter, that is inserted between two Ethernet devices. The PD can be any device that requires power, such as an access point, a camera, or a phone.

One of the factors that affects PoE performance is voltage drop, which is the reduction of voltage that occurs as current flows through a cable due to its resistance. Voltage drop can cause power loss and inefficiency in PoE systems, as well as damage to PDs if the voltage falls below their minimum requirement. To minimize voltage drop, it is recommended to use high-quality cables with low resistance and short length. Among the common types of Ethernet cables, CAT6 has the lowest resistance and therefore the lowest voltage drop compared to Cat5 or CAT5e. CAT6 also has higher bandwidth and data rate than Cat5 or CAT5e, making it more suitable for PoE applications. References: 1, Chapter 7, page 263; 2, Section 4.4

What prevents each station from using all the airtime when other client stations are actively communicating in the same BSS is CSMA/CA. CSMA/CA stands for Carrier Sense Multiple Access with Collision Avoidance and is a media access control method used by WLAN devices to share the wireless medium. CSMA/CA works by having each station sense the medium before transmitting a frame. If the medium is busy (i.e., another station is transmitting), the station defers its transmission until the medium is idle. If the medium is idle, the station waits for a random backoff period before transmitting. This way, CSMA/CA reduces the chances of collisions and ensures fair access to the medium for all stations. CSMA/CA also uses positive acknowledgements to confirm successful transmissions and retransmissions to recover from errors. CSMA/CD, DOS prevention, and OFDMA are not used by WLAN devices in a BSS. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 108; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 98.

 This is because the passphrase for WPA2-Personal is case-sensitive and must match exactly on both the AP and the client. If the passphrase is entered incorrectly on the client, the client will not be able to authenticate with the AP and connect to the network. The AP that covers the problem area is not likely to require a firmware update, fail, or be improperly configured, as it is online and works with other clients that have the correct passphrase. To troubleshoot this issue, you can check the passphrase settings on the clients and make sure they match with the AP. You can also try to reconnect the clients to the network or reboot them if necessary. For more information on how to configure WPA2-Personal on your router

802.11 QoS is achieved by giving high priority queues a statistical advantage at winning contention. 802.11 QoS is based on the Enhanced Distributed Channel Access (EDCA) mechanism, which defines four access categories (ACs) for different types of traffic: Voice, Video, Best Effort, and Background. Each AC has its own transmit queue and contention parameters, such as Arbitration Interframe Space (AIFS), Contention Window (CW), and Transmission Opportunity (TXOP). These parameters determine how long a station has to wait before transmitting a frame and how long it can occupy the channel. Higher priority ACs have shorter AIFS, smaller CW, and longer TXOP, which means they have more chances to access the channel and send more data than lower priority ACs. However, this does not guarantee that higher priority ACs will always win the contention, as there is still a random backoff process involved. Therefore, 802.11 QoS is a statistical service that provides different levels of service quality based on traffic categories. References: , Chapter 10, page 403; , Section 6.1

When a station scans for available wireless networks, it listens for beacon frames sent by APs. A beacon frame contains information about the BSS, such as SSID, supported rates, channel, security, etc. The station also measures the signal strength of the beacon frames, which indicates how well the station can communicate with the AP. The signal strength is usually expressed in dBm or RSSI units. The higher the signal strength, the better the connection quality and performance. Therefore, the station can use the signal strength of AP beacons as the primary metric to select the best AP for connectivity to the desired BSS12. References: CWNA-109 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 249; CWNA-108 Study Guide, Chapter 6: Wireless LAN Devices and Topologies, page 243.

https://7signal.com/802-11ac-migration-part-2-whats-nobodys-telling-you-about-80mhz-and-160mhz-channel-bonding

The clients are all 802.11n STAs or lower is the likely cause of this behavior. If a WLAN with 100 802.11ac access points is configured to use 80 MHz channels, but only 40 MHz communications are seen in a particular BSS, it means that the clients in that BSS do not support 80 MHz channels. This could be because they are using older standards, such as 802.11n or lower, that do not support 80 MHz channels. Alternatively, they could be using newer standards, such as 802.11ac or ax, but have their channel width settings limited to 40 MHz or lower due to device capabilities or configuration options. In either case, the AP will adapt to the client’s channel width and use only 40 MHz of the 80 MHz allocated bandwidth to communicate with them. This will reduce the potential throughput and efficiency of the WLAN. References: , Chapter 3, page 111; , Section 3.2

The channel that can be used for VHT transmissions according to the 802.11 specification is channel 144. VHT stands for Very High Throughput and is the PHY layer specification for 802.11ac devices. VHT transmissions can use channel bandwidths of 20 MHz, 40 MHz, 80 MHz, or 160 MHz in the 5 GHz band. Channel 144 is one of the channels in the 5 GHz band that can support VHT transmissions with any of these bandwidths. Channel 6, channel 1, and channel 11 are channels in the 2.4 GHz band that cannot support VHT transmissions, as they are only compatible with legacy (802.11b/g/n), HT (802.11n), or ERP (802.11g) transmissions with up to 20 MHz bandwidth. References: [CWNP Certified Wireless Network Administrator Official Study Guide: Exam CWNA-107], page 214; [CWNA: Certified Wireless Network Administrator Official Study Guide: Exam CWNA-106], page 204.

An access point is configured by a WLAN controller in the management plane of the three networking planes. The management plane is responsible for the configuration, administration, and monitoring of network devices, such as access points, switches, routers, and controllers. The WLAN controller communicates with the access point using a management protocol, such as CAPWAP or SNMP, to send configuration commands and receive status information. The control plane is responsible for the routing, switching, and forwarding of network traffic, such as data frames and control frames. The WLAN controller may also participate in the control plane by performing functions such as authentication, encryption, roaming, and load balancing. The security plane is responsible for the protection of network devices and data from unauthorized access, modification, or disclosure. The WLAN controller may also participate in the security plane by implementing features such as firewall, VPN, IDS/IPS, and WIPS. The data plane is responsible for the transmission and reception of user data, such as voice, video, or web traffic. The WLAN controller may or may not participate in the data plane depending on the architecture of the WLAN. In some cases, the access point forwards the user data directly to the wired network without involving the WLAN controller (distributed data forwarding). In other cases, the access point tunnels the user data to the WLAN controller before forwarding it to the wired network (centralized data forwarding). References: CWNA-109 Study Guide, Chapter 9: Wireless LAN Architecture, page 279

Station-to-station traffic blocking is a security feature that prevents wireless clients from communicating with each other on the same network. This can prevent active attacks such as man-in-the-middle, ARP spoofing, or denial-of-service that hackers may launch from their devices against other users in a public Wi-Fi hotspot. By enabling station-to-station traffic blocking by the access points in the hotel, Lynne can decrease the likelihood of such attacks on his customers’ wireless computers. This feature can be configured on most wireless APs or controllers345. References: CWNA-109 Study Guide, Chapter 10: Wireless LAN Security, page 427; CWNA-108 Study Guide, Chapter 10: Wireless LAN Security, page 417; Wireless Station-to-Station Traffic Being Blocked.