4A0-220 Nokia GMPLS-Controlled Optical Networks Questions and Answers

A Label Switched Path (LSP) is the path created by MPLS nodes that use labels to forward packets across the network. A label is a short identifier that is attached to each packet and indicates the next hop or destination of the packet. The nodes use a label forwarding table to switch packets based on their labels, without inspecting the packet headers. This can improve the performance, security, and quality of service of the network. An LSP can be established by using GMPLS protocols such as OSPF-TE and RSVP-TE, which exchange information about the network topology, resources, and constraints. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, GMPLS - Nokia

A network with ROADM GMPLS nodes and optical transponder connections could have both L0 and L1 restoration capabilities. L0 restoration refers to the ability of the network to recover from failures at the optical layer, such as fiber cuts or node failures, by rerouting the affected LSPs to alternative paths at the same layer. L0 restoration can be achieved by using GMPLS signaling protocols, such as RSVP-TE or CR-LDP, to establish backup LSPs in advance or on demand. L0 restoration can provide fast recovery times and high availability for optical services34. L1 restoration refers to the ability of the network to recover from failures at the sub-wavelength layer, such as transponder failures or wavelength unavailability, by rerouting the affected LSPs to alternative paths at a higher layer. L1 restoration can be achieved by using GMPLS routing protocols, such as OSPF-TE or ISIS-TE, to advertise the sub-wavelength information and availability to other nodes in the network. L1 restoration can provide more flexibility and efficiency for sub-wavelength services56. References:

• 3: GMPLS - Nokia
• 4: Generalized Multi-Protocol Label Switching - Wikipedia
• 5: Sub-Wavelength Switching - Nokia
• 6: Sub-Wavelength Switching in Optical Networks - IEEE Xplore

RSVP-TE Notify message is a message type defined in the RSVP-TE protocol, which is an extension of the RSVP protocol for MPLS traffic engineering. RSVP-TE Notify message is used to inform non-adjacent nodes of LSP events, such as setup, modification, or teardown. This allows the nodes to update their local state information and perform actions based on the notification. For example, a Notify message can be used to trigger a fast reroute mechanism in case of a link or node failure12. References:

• 1: RFC 3473 - Generalized Multi-Protocol Label Switching (GMPLS) Signaling Resource Reservation Protocol-Traffic Engineering (RSVP-TE) Extensions
• 2: RFC 3471 - Generalized Multi-Protocol Label Switching (GMPLS) Signaling Functional Description

A Nominal Route in a GMPLS network is the optimal path that meets the Traffic Engineering (TE) constraints for a given LSP request. A Nominal Route is calculated by the NFM-T using the Constrained Shortest Path First (CSPF) algorithm, which takes into account parameters such as bandwidth, latency, priority, protection type, and other QoS attributes. A Nominal Route is stored in the NFM-T database and can be used to provision LSPs over the network. A Nominal Route can differ from the Current Route, which is the actual path that the LSP is taking at a given time, due to network changes or failures. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, Nokia Advanced Optical Network Management with NFM-T Course | Nokia

The OSPF-TE protocol is an extension of the Open Shortest Path First (OSPF) protocol that is used to exchange information about the state of links in a GMPLS network. OSPF-TE advertises link attributes such as bandwidth, latency, priority, protection, or switching capabilities to other nodes in the same area. OSPF-TE enables nodes to build a Traffic Engineering Database (TED) that contains the topology and resource information of the network. OSPF-TE helps nodes to perform CSPF calculations and establish LSPs using RSVP-TE signaling. References : Open Shortest Path First - Wikipedia, Understand Open Shortest Path First (OSPF) - Design Guide, RSVP-TE and OSPF-TE extensions for GMPLS

Quality of Service (QoS) in GMPLS is the ability to set constraints such as latency and priority for different kinds of services. This means that GMPLS can allocate network resources according to the specific requirements of each service, such as voice, video, or data. For example, a voice service may need low latency and high priority, while a data service may need high bandwidth and low priority. GMPLS can use Traffic Engineering (TE) extensions to OSPF and RSVP protocols to advertise and reserve network resources based on QoS parameters. References : [Nokia GMPLS-controlled Optical Networks Course | Nokia], [Quality of Service - Nokia]

The Soft Shutting Down state in the NFM-T is an administrative maintenance state where services stay up but no new traffic can be routed over the TE-link. This state is used to prepare a TE-link for maintenance or decommissioning without affecting the existing services. The NFM-T sets the TE-link to Soft Shutting Down state by sending a Notify message with the Administrative State Change flag to the head-end node of the TE-link. The head-end node then stops accepting new LSP requests over the TE-link and sends a PathErr message with the Administrative State Change flag to all the tail-end nodes of the LSPs in the TE-link. The tail-end nodes then stop sending new traffic over the LSPs and send a ResvErr message with the Administrative State Change flag to all the intermediate nodes of the LSPs. The intermediate nodes then update their routing tables and stop forwarding new traffic over the LSPs. The existing traffic, however, continues to flow over the LSPs until they are manually deleted or rerouted by the NFM-T. References : Nokia GMPLS-controlled Optical Networks Course | Nokia, Nokia Advanced Optical Network Management with NFM-T Course | Nokia

GMPLS stands for Generalized Multi-Protocol Label Switching, which is a protocol suite that extends MPLS to control different types of switching technologies, such as optical, TDM, and packet switching1. The meaning of Generalized in GMPLS is that it can be used for traffic types other than data packets, such as wavelengths, time slots, or fibers2. GMPLS can also use implicit labels that are derived from the physical properties of the data stream, such as wavelength or timeslot, instead of explicit labels that are carried in the packet header3. This allows GMPLS to support various transport networks and applications, such as optical transport networks (OTN), wavelength switched optical networks (WSON), and automatic switched optical networks (ASON)4. References:

• 1: Nokia GMPLS-controlled Optical Networks Course | Nokia
• 2: What is MPLS and GMPLS? - Metaswitch
• 3: Generalized Multi-Protocol Label Switching - Wikipedia
• 4: GMPLS - Nokia

The 3R resource is a type of optical regeneration resource that can be used to extend the reach of optical signals in a GMPLS-controlled optical network. The 3R resource performs three functions: reshaping, retiming, and reamplifying the optical signal. The 3R resource can be added to the Network Planning Application (NPA) in the Nokia Network Functions Manager for Transport (NFM-T) through the Constraint Wizard. The Constraint Wizard is a tool that allows the user to define various constraints and parameters for the network design, such as optical impairments, wavelength availability, protection schemes, and regeneration resources. The user can select the 3R resource from the list of available resources and specify its location, capacity, and cost. The NPA then uses this information to perform feasibility checks and path computation for the LSP requests12. References:

• 1: Nokia GMPLS-controlled Optical Networks Course | Nokia
• 2: Nokia Network Functions Manager for Transport User Guide | Nokia